29 rr series 1.0 description 2.0 mechanical 4.0 part number thin film technology has achieved high performance chip resistors with low price and reliable supply. the parts offer excellent performance and tolerance in tcr, current noise, linearity, and are intended for high frequency circuit applications. precise dimensions minimize errors during mounting. tight tolerances allow for cost sav- ings due to circuit simplification and elimination of trim pots for adjustment. dimension mm rr0306 (0201) rr0510 (0402) rr0816 (0603) rr1220 (0805) rr1632 (1206) rr2632 (1210) l 0.60 0.05 1.00 0.05 1.60 0.20 2.00 0.20 3.20 0.20 3.20 0.20 w 0.30 0.05 0.50 0.05 0.80 0.20 1.25 0.20 1.60 0.20 2.60 0.20 p 0.12 0.05 0.20 0.10 0.30 0.20 0.40 0.20 0.50 0.20 0.50 0.20 t 0.23 0.03 0.35 0.05 0.40 0.10 0.40 0.10 0.40 0.10 0.45 0.10 l p w dimension mm schematic rr 0816 p - 102 - d - ** thin film chip resistor product designator resistance tolerance temperature coefficient of resistance resistance value (e-series) package size for e-24 values of rr0306, rr0510, rr0816 and rr1220 use three digits when ordering. rr 1632 p - 1001 - d - ** manufacturer(s) of the products described on this page are indicated by their respective logos. m a n a g e m e n t s y s t e m c e r t i f i e d quality system m a n a g e m e n t s y s t e m c e r t i f i e d quality system t type rr0306 (0201) rr0510 (0402) rr0816 (0603) rr1220 (0805) rr1632 (1206) rr2632 (1210) power 1/ 20 w 1/ 16 w 1/ 16 w 1/ 10 w 1/ 8 w 1/ 4 w resistance tol. 1.0% 0.5% 0.5% 0.5% 0.5% 0.5% (code) (f) (d) (d) (d) (d) (d) r- value (ohm) 10-30 33-22 k 10-97.6 100-100 k 10-97.6 100-360 k 10-97.6 100-1 m 10-49.9 51-1 m 10-49.9 51-2 m tcr (ppm/c) 100 25 100 25 50 25 50 25 50 25 50 25 (r) (p) (r) (p) (q) (p) (q) (p) (q) (p) (q) (p) range e-24 e-24/e-96 e-24/e-96 e-24/e-96 e-24/e-96 24/e-96 max op. volt 15 v 25 v 75 v 100 v 150 v 200 v package 5,000 pcs./reel 10,000 pcs./reel 5,000 pcs./reel 5,000 pcs./reel 5,000 pcs./reel 1,000-5,000 pcs./reel operating temp -55c - +125c 3.0 electrical ssm manufactured products yds manufactured products rohs compliant products (c for ssm; lf for yds)
standard resistance values please refer to the following table of the standard e-series application for resistors. series significant figures e-12 1.00 1.20 1.50 1.80 2.20 2.70 3.30 3.90 4.70 5.60 6.80 8.20 e-24 1.00 1.10 1.20 1.30 1.50 1.60 1.80 2.00 2.20 2.40 2.70 3.00 3.30 3.60 3.90 4.30 4.70 5.10 5.60 6.20 6.80 7.50 8.20 9.10 e-96 1.00 1.02 1.05 1.07 1.10 1.13 1.15 1.18 1.21 1.24 1.27 1.30 1.33 1.37 1.40 1.43 1.47 1.50 1.54 1.58 1.62 1.65 1.69 1.74 1.78 1.82 1.87 1.91 1.96 2.00 e-6 1.00 1.50 2.20 3.30 4.70 6.80 preferred value of resistance shall be composed by significant figures shown in the above table and multipliers including x10 ohm, x100 ohm, x1,000 ohm, x10,000 ohm, and x100,000 ohm. ? specifications in this catalog are subject to change for future improvement without prior notice ? the contents of this catalog are current as of september 2006 ? the susumu world group companies, including susumu company ltd., thin film technology corporation, yokohama denshi seiko company, ltd., and cyntec company ltd., do not recommend the use of their prod- ucts in any life support applications where failure or malfunction of the product can or may cause failure of a life support device or system, or effect in any manner its safety or effectiveness. should the customer use a product in a life support application then, in that event, the susumu world group companies disclaim any and all express or implied warranties as to fitness for any particular purpose or as to merchantability. ? this is catalog 2006 volume 1 ? most current version of catalog may be found on the website, www.thin-film.com susumu world group copyright ? by thin film technology 2005-2006 published by the p h ilter c i rcuits division, 1980 commerce drive, north mankato, mn 56003 all rights reserved. this book, or parts thereof, may not be reproduced in any form without permission. printed in the united states of america. pn 100105 x400 i90 c c olophon: concept/writing/illustration/art direction: mark brooks production: linda brown. production notes: this catalog was created electronically using quark xpress and adobe illustrator. 2.05 2.10 2.15 2.21 2.26 2.32 2.37 2.43 2.49 2.55 2.61 2.67 2.74 2.80 2.87 2.94 3.01 3.09 3.16 3.24 3.32 3.40 3.48 3.57 3.65 3.74 3.83 3.92 4.02 4.12 4.22 4.32 4.42 4.53 4.64 4.75 4.87 4.99 5.11 5.23 5.36 5.49 5.62 5.76 5.90 6.04 6.19 6.34 6.49 6.65 6.81 6.98 7.15 7.32 7.50 7.68 7.87 8.06 8.25 8.45 8.66 8.87 9.09 9.31 9.53 9.76
|
